Description
Martin 90356800 Exterior PixLine 20 RGB, 1280mm, Square
The Exterior PixLine 20 is a linear LED video fixture for media facades and creative installations. The Exterior PixLine 20 can be combined with a wide variety of lenses and diffusers for the right look for every application. The Exterior PixLine 20 is driven by the Martin P3 System Controller family for easy setup and video display, and it is also backwards compatible with DMX for smaller setups. The fixtures can be fully customized in terms of length and color to match every installation requirement, while the power source is hidden.
- Wide range of pixel pitch, lens and diffuser options for flexibility of look
- Fully outdoor-rated and customizable in terms of length and color
- Easy setup and cabling for clean installation
Features
- 20 mm pixel pitch
- 125 cd per meter calibrated
- 80 lumen per foot calibrated
- High-quality 16-bit per color image processing technology
- Pixel-level brightness and color calibration for optimal image quality
- P3/DMX controllable (automatic protocol detection)
- Intuitive mapping and addressing via P3 System Controller
- Combined power/data input (single cable for power and data input)
- Supported by integrated power and data processor (P3 PowerPort 1500 or P3 PowerPort 1000 IP) and simple cabling system
- Available in standard length of 1280 mm and 320 mm (customized lengths also available)
Specifications
Physical
- Length: Available in 310 mm and 1270 mm length versions* *
- Fixtures must be installed with a 10 mm gap to allow for thermal expansion
- Custom lengths are available to special order on project basis as follows:
- Minimum custom length: 300 mm (11.9 in.)
- Maximum custom length: 2000 mm (78.8 in.)
- Custom length increments: 20 mm (0.8 in.)
- NB: To allow for thermal expansion, fixtures are 10 mm shorter than the nominal lengths given above
- Width: 27 mm (1.1 in.)
- Height with flat diffuser / clear front: 32 mm (1.3 in.)
- Height with flat diffuser / clear front in mounting profile: 74 mm (3.0 in.)
- Height with asymmetric wallwasher lens: 42 mm (1.7 in.)
- Height with asymmetric wallwasher lens in mounting profile: 84 mm (3.4 in.)
- Height with round diffuser: 42 mm (1.7 in.)
- Height with round diffuser in mounting profile: 84 mm (3.4 in.)
- Weight: 1.2 kg / m (0.9 lbs. per foot)
Control and Programming
- Control options: Martin P3™ System Controller via Martin P3™ PowerPort 1500 / Martin P3™ PowerPort 1000 IP, and/or
- DMX Protocol detection: Automatic Control modes: RGB, basic, segment and pixel-level
- DMX channels: 3/10/13/31/55/199
- Setting and addressing: Martin P3™ System Controller or RDM-compliant controller
- Control resolution: 16-bit (P3) or 8-bit (DMX) control of each color
- Color and intensity calibration: Pixel-level
- DMX compliance: USITT DMX512-A
- RDM compliance: ANSI/ESTA E1.20
- Firmware update: Via Martin P3™ System Controller
Control/User Interface
Device status: Multi-color visual indication
Device test and reset:Magnetic pushbutton to call up local test patterns and reset device
Optics
Options
- Flat diffuser
- Round Diffuser
- Square Diffuser
- Clear Front Linear Asymmetric Lens (Graze version)
- Minimum LED lifetime: 50 000 hours (to >70% luminous output)
- * *Figure obtained under manufacturer’s test conditions
Photometric Data
- Color resolution: 16 bits per color (48 bit per pixel)
- Viewing angle: 120° x 120°
- Pixels per meter: 50 Pitch (pixel center-to-center): 20.00 mm
- Luminous intensity, calibrated mode: 125 cd per meter*
- Total output, calibrated mode: 375 lumens per meter*
- Total output, calibrated mode: 4 166 nits (modules spaced 30 mm center-to-center)* *Preliminary data, figures are approximate
Video processing
- Brightness control
- Gamma correction and control
- Color temperature control
- Color space control
- Calibration processing
- Synchronization
Signal Protocol
- P3 (via Martin P3™ PowerPort) or DMX
Construction
- Base: Extruded aluminum profile
- Color: Clear anodized (customized colors available on project basis)
- Protection rating: IP66
- Impact resistance: IK05 RoHS compliant
Installations
- Orientation: Any
- Mounting: Slot for locking nuts on back of profile (M6) and/or installation mounting profile
Connections
- Power and data input: 6-pin custom (BBD) IP66-rated
- Power and data thru: 6-pin custom (BBD) IP66-rated
- Hot plugging compatible
Electrical
- Nominal input voltage: 48V DC +/- 4%
- Power supply options: Martin P3™ PowerPort 1500, Martin P3™ PowerPort 1000 IP or generic 48 VDC PSU
- Max. total power consumption: 17 W per meter (at max. intensity, full white)
Thermal
- Cooling: Convection
- Maximum ambient temperature (Ta max.): 55° C (131° F)
- Minimum ambient temperature (Ta min.): -20° C (-4° F)
- Total heat dissipation (calculated, +/- 10%): 55 BTU/hr per meter
Approvals
- EU safety: EN 60950-1, EN 60950-22 EU EMC:
- EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3
- US safety: UL 60950-1, UL 60950-22 US EMC: FCC Part 15 Class A
- Canadian safety: CSA C22.2 No. 60950-1, No. 60950-22
- Canadian EMC: ICES-003 Class A
- Australia/NZ: RCM
Accessories
- Magnetic Test Tool, set of 10: P/N 91610139
Mounting hardware
- Exterior PixLine™ 20 Mounting Profile, 310 mm (12.2 in.), aluminum: P/N 91611700
- Exterior PixLine™ 20 Mounting Profile, 1270 mm (50.0 in.), aluminum: P/N 91611710
- Exterior PixLine™ Mounting Profile Locks, set of 10: P/N 91611725
Cables
- Cables Power + Data Input Cable, 4-pin male XLR (for P3 PowerPort 1500) to fem. BBD, 0.25 m (0.9 ft.): P/N 11840257
- Power + Data Input Cable, 5-pin male XLR + wire tails (for PSU) to female BBD, 0.25 m (0.9 ft.): P/N 11840276
- Power + Data Input Cable, 5-pin male XLR + male Tripix IP66 PSU to fem. BBD, 0.25 m (0.9 ft.): P/N 11840275
- Power + Data Extension Cable, Installation type CMX, BBD-BBD 1 m (3.3 ft.): P/N 11840270
- Power + Data Extension Cable, Installation type CMX, BBD-BBD, 2.5 m (8.2 ft.): P/N
Delivery & Returns
At Gear Club Direct, we want you to be happy with your purchase. We understand that there are times when once a product is received, it may not be what you needed or wanted after all. So, we will gladly accept your qualifying return within 15 days of the delivery date. After 15 days of the delivery date, all sales are final.
The Return Process
Customers are required to obtain a Pre-Authorization to return any product. To submit a request for a return, simply log in to your account and request a return and one of our sales representatives will contact you within 24-48 business hours. If you do not have an account with us, please open a help ticket, providing as much detail as possible and whether you are requesting a refund or an exchange. READ MORE