Martin Ext PixLine 20 RGB 1270mm Diff Front Alu

The Exterior PixLine 20 is a  linear LED video fixture for media facades and creative installations. The Exterior PixLine 20 can be combined with a wide variety of lenses and diffusers for the right look for every application. The Exterior PixLine 20 is driven by the Martin P3 System Controller family for easy setup and video display, and it is also backwards compatible with DMX for smaller setups. The fixtures can be fully customized in terms of length and color to match every installation requirement, while the power source is hidden.

• Wide range of pixel pitch, lens and diffuser options for flexibility of look
•  Fully outdoor-rated and customizable in terms of length and color
•  Easy setup and cabling for clean installation

Features

• 20 mm pixel pitch
• 125 cd per meter calibrated
• 80 lumen per foot calibrated
• High-quality 16-bit per color image processing technology
• Pixel-level brightness and color calibration for optimal image quality
• P3/DMX controllable (automatic protocol detection)
• Intuitive mapping and addressing via P3 System Controller
• Combined power/data input (single cable for power and data input)
• Supported by integrated power and data processor (P3 PowerPort 1500 or P3 PowerPort 1000 IP) and simple cabling system
• Available in standard length of 1280 mm and 320 mm (customized lengths also available)

Specifications

Physical

• Length: Available in 320 mm (12.6 in.) and 1280 mm (50.4 in.) length versions
• Width: 27 mm (1.1 in.)
• Height:

  with flat diffuser / clear front: 32 mm (1.3 in.)
  with flat diffuser / clear front in mounting profile: 74 mm (3.0 in.)
  with graze (asymmetric wallwasher) lens: 42 mm (1.7 in.)
  with asymmetric wallwasher lens in mounting profile: 84 mm (3.4 in.)
  with round diffuser: 42 mm (1.7 in.)
  with round diffuser in mounting profile: 84 mm (3.4 in.)

• Weight: 1.2 kg / m (0.9 lbs. per foot)
• Custom lengths are available to special order on project basis as follows:

  Minimum custom length: 300 mm (11.9 in.)
  Maximum custom length: 2000 mm (78.8 in.)
  Custom length increments: 20 mm (0.8 in.)

• NB: To allow for thermal expansion, fixtures are 10 mm shorter than the nominal lengths given above
• *Fixtures must be installed with a 10 mm gap to allow for thermal expansion

Control and Programming

• Control options: Martin P3™ System Controller via Martin P3™ PowerPort 1500 / Martin P3™ PowerPort 1000 IP, and/or DMX
• Control modes: RGB, basic, segment and pixel-level
• Control resolution: 16-bit (P3) or 8-bit (DMX) control of each color
• Protocol detection: Automatic
• Setting and addressing: Martin P3™ System Controller or RDM-compliant controller
• DMX channels: 3/10/13/31/55/199
• Color and intensity calibration: Pixel-level
• Firmware update: Via Martin P3™ System Controller
• DMX compliance: USITT DMX512-A
• RDM compliance: ANSI/ESTA E1.20

Control/User Interface

• Device status: Multi-color visual indication
• Device test and reset: Magnetic switch to call up local test patterns and reset device

Optics

• Options:

  Clear Front: Viewing angle 110°
  Flat Diffuser: Viewing angle 160°
  Round Diffuser: Viewing angle 260°
  Square Diffuser: Viewing angle 300°
  Asymmetric graze Lens: Beam angle 25° X 85°

• Minimum LED lifetime: 50,000 hours (to >70% luminous output)*
• LED manufacturer: Osram
• *Figure obtained under manufacturer’s test conditions

Photometric Data

• Color resolution: 16 bits per color (48 bit per pixel)
• Pixels: 50 per meter
• Pitch (pixel center-to-center): 20.00 mm
• Luminous intensity: 125 cd per meter (calibrated mode)
• Total output, calibrated mode: 250 lumens per meter (4,166 nits (modules spaced 30 mm center-to-center))

Video Processing

• Brightness control
  Gamma correction and control
  Color temperature control
  Color space control
  Calibration processing
  Synchronization

Signal Protocol

• P3 (via Martin P3™ PowerPort) or DMX

Construction

• Color: Clear anodized (customized colors available on project basis)
• Base: Extruded aluminum profile
• Protection rating: IP66
• Impact resistance: IK05
• Corrosion resistance: C5-M (very high corrosivity/marine, ISO 2944)
• RoHS compliant

Installation

• Mounting: Slot for locking nuts on back of profile (M6) and/or installation mounting profile
• Orientation: Any

Connections

• Power and data input: 6-pin custom (BBD) IP66-rated
• Power and data thru: 6-pin custom (BBD) IP66-rated
• Hot plugging compatible

Electrical

• Nominal input voltage: 48V DC +/- 4%
• Power supply options: Martin P3™ PowerPort 1500, Martin P3™ PowerPort 1000 IP, Martin IP66 PSU or generic 48 VDC PSU
• Maximum total power consumption: 17 W per meter (at max. intensity, full white)
• Surge protection: 4 KV

Thermal

• Cooling: Convection
• Maximum ambient temperature (Ta max.): 55° C (131° F)*
• Minimum ambient temperature (Ta min.): -30° C (-22° F)
• Total heat dissipation (calculated, +/- 10%): 55 BTU/hr per meter
• *Above this temperature, the fixture regulates output to protect from overheating (P3 thermal throttling)

Approvals

• EU safety: EN 60950-1, EN 60950-22
• EU EMC: EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3
• US safety: UL 60950-1, UL 60950-22
• US EMC: FCC Part 15 Class A
• Canadian safety: CSA C22.2 No. 60950-1, No. 60950-22
• Canadian EMC: ICES-003 Class A
• Australia/NZ: RCM